Another important point to remember is to have a trenches level. It is ideal to lay out the pieces and assemble them before putting them into the trench. First, start out by cutting the PVC pipes with either a hack saw or pipe cutter. Using a knife or fine file to smooth out the edges and then it is time to position the pipe. To do so, install the pipe into the fitting followed by adjusting so the pipe is in the correct position. To save time and energy, mark the pipe and fitting line with a marker for reference, this way it is easier to find the position after cementing.
Once the pip is cut and positioned, you want to prime the pipe by removing it from the fitting. Clean the surfaces so you can use a solvent primer to matte the finishes. Once this step is complete, brush all surfaces, inside and out with cement.
Once the preparation of the pipe is finished, it is time to install and align the PVC piping. To do so, push the pipe into the fitting and use your reference lines as a guide, then twist the pipe in order to align it with the marks.
By doing this, you are allowing the cement to be spread. It is important to be able to work quickly with this step as the adhesive sets quickly; 30 seconds quickly! There are a number of ways to connect the sprinkler heads to the pipes. However, anyone attempting the DIY route should be sure to clear any debris from the line before connection to avoid blockages.
The 4th step is to connect the sprinkler system to the water supply and you can do so by following one of these two ways. Like garden hoses, the line can be connected to the outside water faucet which can be found outside of the house either in the backyard or side and in some cases, the front. Want More DIY? The second way to connect is by doing so directly through the service line. If someone decides to go this route, shut off the main water supply, and then cut out 1 inch from the line and add a compression tee fitting.
In addition to this, add an additional valve so the system's water supply can be controlled independently. If the water is ever siphoned back into the supply, chemicals from the lawn could enter and cause serious damage. Reverse pressure from the system can also encourage backflow. It is no wonder this is a very important step. To prevent backflow, a system will need to be installed, and just like the sprinkler heads, it is important to check the manufacturer's instructions to ensure property and correct installation.
Once everything is complete it is time to set up the control system. Set up and program timers, zones and more. Having one zone timed for 30 minutes, and another zone set up for an hour is also possible.
Knowing how much water is needed for each zone is important so the control system can accurately be set up. It is also a good idea to set the control system to have a timer for shut off. By installing a sprinkler system correctly, and making good use of it, your lawn will be gorgeous all year round!
Sign in to your account. Phone Number Need to reset your phone number? Don't have an account with us? Click here to sign up. June 24, Plan Before diving into the installation of the sprinkler system, it is important to plan and prepare. There are a number of different types of grasses, some of which include: St.
Augustine Grass - Warm season grass that is mostly found in warm regions like Florida and the Gulf Coast region. This grass needs plenty of moisture to stay healthy. Having a sprinkler system that can cover the whole lawn is crucial. Fine Grass - Another grass that needs above-average watering Determining the type of soil is also important to determine the absorption level. For these reasons it is not surprising that it is worth installing one in your yard. The installation process is not overly complicated, although it does require some skill.
This post will indicate the steps and materials necessary to teach you how to install a sprinkler system, so you can decide if you have enough skills to do the assembly yourself or you need to hire a professional.
In any case, it is always good to know how these irrigation systems work, because that knowledge will help you solve the common circumstances that may arise once it is running. Your automatic sprinkler irrigation system will consist of the following main elements, which you will need to assemble:. The programmer is the brain, the control unit that manages the irrigation times of each irrigation sector. Solenoid valves are connected by cables to the programmer, and are in charge of opening and closing the different irrigation sectors depending on what it indicates, operating each area or irrigation phase independently.
Polyethylene pipe ; in different measures, water will flow through it towards the emitters. The pipe you use must be manageable, flexible and easy to cut. Irrigation emitters are the elements that project water throughout the surface, those responsible for carrying out irrigation. They are chosen based on what is going to be watered and the extension of the surface. Each type of emitter has a utility, scope and angle of irrigation, for small and large areas of grass.
Polyethylene irrigation accessories. Depending on the type and characteristics of your installation, you will need other additional accessories, which you will see later when you explain the steps to carry out the assembly. Suffice it to say for now that the most frequent are collars, manifolds for solenoid valves, and elbows of different sizes.
This is your starting point, you have to know where you are going to get the water that you will then distribute. Normally you can use the general entrance pipe to the house as a water intake, in which case you will use a tee to draw the line for irrigation water, or a tap that you have in the garden. Each irrigation area in which you divide our plot has its own pipeline or circuit, which will be controlled by an electrovalve located at the beginning of said circuit.
The irrigation head is the set of solenoid valves and other control elements of all the circuits or phases of the installation, which are usually grouped in the same space to facilitate their revision and manipulation.
Keep in mind that this must be connected by cable to the solenoid valves. This data will help you determine what type and how many emitters you can use. The next thing is to make a plan of the garden, preferably to scale. Said plan must include the following points:. Irrigation programmer: the place where you place it must be protected from inclement weather and equipped with electricity. Irrigation head: areas to irrigate, including grass, trees, shrubs, etc.
Once you have your plan, now you buy the adequate quantity of main elements length of pipe, solenoid valves, emitters and programmer that will make up our automatic home irrigation and prepare to assemble the structure. Although you will have to add some accessories that will depend on the characteristics of our installation. Once you have all the tools in your hands you will get to work, you must do ten tasks to complete your installation:.
Mark the layout of the pipes that will be distributed throughout the plot, using twine or marking on the ground. Dig the trenches through which the pipes will run, if your installation is underground the usual in case of sprinkler irrigation.
Pull a pipe from the water intake to the place where you are going to place the irrigation head. Assemble the irrigation head, connect it to the pipe coming from the water intake and lodge it in the manhole, in case the installation is buried.
Distribute the pipeline through the open trenches from the head to the different points where the water must arrive. Place the irrigation emitters of each zone. In some cases, most will be emerging turbine sprinklers, and some diffusers.
Make the electrical connection from the programmer to the solenoid valves. Verify that everything is working correctly and the irrigation angles of the sprinklers are adjusted. Once you make sure there are no water leaks, you cover the trench by burying the pipe.
Get a quote online to receive a fast, free estimate for your lawn care needs. Landscaping How to install a sprinkler system 4 min read. How to install a sprinkler system Want to save time and money in the summer when watering your lawn? Elements of the irrigation system Your automatic sprinkler irrigation system will consist of the following main elements, which you will need to assemble: The programmer is the brain, the control unit that manages the irrigation times of each irrigation sector.
Planning Locate the water intake This is your starting point, you have to know where you are going to get the water that you will then distribute.
Choose the location where you will place our irrigation head Each irrigation area in which you divide our plot has its own pipeline or circuit, which will be controlled by an electrovalve located at the beginning of said circuit.
Choose the location of the irrigation controller Keep in mind that this must be connected by cable to the solenoid valves. Measure the flow that you have in the water intake This data will help you determine what type and how many emitters you can use. Map the yard The next thing is to make a plan of the garden, preferably to scale. Said plan must include the following points: Irrigation programmer: the place where you place it must be protected from inclement weather and equipped with electricity.
Installation Once you have your plan, now you buy the adequate quantity of main elements length of pipe, solenoid valves, emitters and programmer that will make up our automatic home irrigation and prepare to assemble the structure. Need some help around the yard? How to lay sod Sodding can bring a lawn back to life. Lawn Love lawn care Lawn care guide How to install a sprinkler system.
Albany, NY Lawn Care. Albuquerque, NM Lawn Care. Arlington, VA Lawn Care. Asheville, NC Lawn Care. Atlanta, GA Lawn Care. Augusta, GA Lawn Care. Austin, TX Lawn Care. Bakersfield, CA Lawn Care. Baltimore, MD Lawn Care. Birmingham, AL Lawn Care. Boise, ID Lawn Care. Boston, MA Lawn Care.
Buffalo, NY Lawn Care. Charleston, SC Lawn Care. Charlotte, NC Lawn Care. Chattanooga, TN Lawn Care. Chicago, IL Lawn Care.
0コメント